Carbine Malfunctions, Diagnosis and Remediation, Part 4

At Home

• -Verify you are using only dummy rounds!
• -Carbine, (2) dummy rounds and magazine.
• -With the bolt locked back, insert a magazine with dummy round into the magazine well.
• -Manually drop another dummy round into the ejection port.
• -Release the bolt forward.

Note: “V” Configuration

On the Range

• -Carbine, (1) live round and a magazine with live rounds.
• -With the bolt locked back, insert the magazine with live rounds into the magazine well.
• -Manually drop another live round into the ejection port.
• -Release the bolt forward.

WARNING! If a TAP, RACK is initiated, this malfunction can be made more severe by hammering the rounds deeper into the chamber!

*Finger out of trigger guard.

• -Verify you are using only dummy rounds!
• -Carbine, (3) dummy rounds and a magazine.
• -With the bolt locked back, manually insert a dummy round into the chamber and roll the carbine magazine well up so the dummy round falls into the carrier key channel.
• -Insert magazine with dummy round.
• -Manually insert another round into the receiver.
• Release the bolt forward.

• -Carbine, (1) live round, (1) spent casing and a magazine with live rounds.
• -With the bolt locked back, manually insert a spent casing into the chamber and roll the carbine magazine well up until the spent casing rolls into the carrier key channel.
• -Insert magazine loaded with live rounds.
• -Manually insert another live round into the receiver.
• -Release the bolt forward.

Note: brass above bolt

Triple Feed – MUSH means RIP (RAD)

Operator has attempted to fire and experiences a Triple Feed, feeling a MUSH of the trigger. Remedial action drill is initiated.

Carbine is rolled outboard into high control and magazine is RIPPED out.

*Finger out of trigger guard.

Operator attempts to PULL and HOLD charging handle to rear, but charging handle will not retract. This is a primary indicator that a triple feed or some type of charging handle impingement has occurred.

Rounds in the chamber must be removed prior to remediating charging handle impingement!

PULL and HOLD charging handle back as far as possible, INSERT a finger and DIGITALLY MANIPULATE any stuck casings/rounds out

Transfer carbine to left shoulder for better visual.

Push charging handle forward to reseat.

This MUST be done in order to remediate the charging handle impingement.

Use an expedient tool like the tip of a live round, index finger, Leatherman or corner of magazine.

Hook tool on edge of bolt carrier group and pull rearward while angling magazine well downward so gravity can assist.

Shake carbine until casing lodged in carrier key channel above bolt falls free.

RELEASE bolt carrier forward, access and insert loaded magazine.

RACK, RELOAD, RACK. Sights are reacquired and target(s)/environment are REASSESSED.

Failure To Unlock:

This is where the bolt will not unlock from the chamber. The failure to unlock can be caused by having a dirty weapon (operator error), a bulged casing, worn locking lugs, a lubricated chamber or non-spec ammunition. Remediation of this malfunction can be either administrative or combative, depending upon how tightly the bolt is locked. This malfunction cannot be replicated for training purposes, but in high-round-count courses, it is not uncommon to see one or two.

One combative method to remediate this malfunction is to attempt to put the weapon on safe, collapse the stock, take a knee and elevate the muzzle 45 degrees, depress the charging handle release while robustly striking the buttstock on the ground or floor. The inertia of the bolt carrier may unlock the bolt. This method is commonly referred to as “mortaring.”

While this method may work, it can damage the stock of the firearm and/or bend the buffer tube, rendering the firearm inoperable. Utilizing this technique also limits mobility when assuming a kneeling position, which is not recommended in any combative environment.

Another option is to remain standing, attempt to place the carbine on safe, step forward with one leg, angle the carbine away from your body, tense the muscles of that leg and depress the charging handle release while smartly striking the buttstock against the inner surface of your tensed thigh muscle.

Utilizing this method, there is a very good chance that you will strike the stock hard enough to unlock the bolt but not hard enough to damage the firearm. This method generates enough force to remediate the malfunction and allows the operator to move rapidly if necessary.

Remediating malfunctions efficiently gets you back in action quickly. Although you can take certain actions up front to minimize the number of malfunctions you experience (e.g., using quality magazines and ammo, keeping your weapon clean, replacing worn parts), you may still experience one for any of the reasons outlined throughout this series, and experience it at an inopportune time. Being able to perform the remedial action drills for each malfunction will keep your carbine from turning into a club.